Kia Soul: Engine Mounting Removal and Installation - Engine And Transmission Assembly - Engine Mechanical SystemKia Soul: Engine Mounting Removal and Installation

Kia Soul 2014-2019 PS Service Manual / Engine Mechanical System / Engine And Transmission Assembly / Engine Mounting Removal and Installation

Engine Mounting Bracket
1.
Remove the engine room under cover.
(Refer to Engine And Transaxle Assembly - "Engine Room Under Cover")
2.
Install the jack under the edge of lower oil pan to support the engine.
  
Put the rubber block between the jack and oil pan to avoid damaging the oil pan.
3.
Remove the engine mounting support bracket (A).
Tightening torque
Nut (B) :
78.5 ~ 98.1 N.m (8.0 ~ 10.0 kgf.m, 57.9 ~ 72.3 lb-ft)
Bolt (C), Nuts (D) :
58.8 ~ 73.5 N.m (6.0 ~ 7.5 kgf.m, 43.4 ~ 54.2 lb-ft)

4.
Remove the engine mounting bracket (A).
Tightening torque :
49.0 ~ 63.7 N.m (5.0 ~ 6.5 kgf.m, 36.2 ~ 47.0 lb-ft)

5.
Install in the reverse order of removal.
Roll Rod Bracket
1.
Remove the roll rod bracket (A).
Tightening torque
Bolt (B):
107.9 ~ 127.5 N.m (11.0 ~ 13.0 kgf.m, 79.6 ~ 94.0 lb-ft)
Bolts (C):
49.0 ~ 63.7 N.m ( 5.0 ~ 6.5 kgf.m, 36.2 ~ 47.0 lb-ft)

2.
Remove the roll rod mounting support bracket (A).
Tightening torque :
49.0 ~ 68.6 N.m ( 5.0 ~ 7.0 kgf.m, 36.2 ~ 50.6 lb-ft)

3.
Install in the reverse order of removal.
Transaxle Mounting Bracket
1.
Remove the air cleaner assembly.
(Refer to Intake And Exhasut System - "Air Cleaner")
2.
Remove the battery and battery tray.
(Refer to Engine Electrical System - "Battery")
3.
Remove the engine room under cover.
(Refer to Engine And Transaxle Assembly - "Engine Room Under Cover")
4.
Install jack under the transaxle to support it.
5.
Remove the service cover (A).
6.
Remove the transaxle support bracket mounting bolts (A).
Tightening torque :
88.3 ~ 107.9 N.m (9.0 ~ 11.0 kgf.m, 65.1 ~ 79.6 lb-ft)

7.
Remove the transaxle mounting bracket (A).
Tightening torque :
49.0 ~ 63.7 N.m (5.0 ~ 6.5 kgf.m, 36.2 ~ 47.0 lb-ft)

8.
Install in the reverse order of removal.
    Engine Mounting Components
    1. Transaxle mounting bracket 2. Roll road bracket 3. Engine mounting bracket 4. Engine mounting support bracket ...

    Engine And Transmission Assembly Removal
       • Use fender covers to avoid damaging painted surfaces. в ...

    See also:

    Piston and Connecting Rod Disassembly
       • Use fender covers to avoid damaging painted surfaces. • ...

    Brake Pedal. Removal
    1. Turn ignition switch OFF and disconnect the negative (-) battery cable. 2. Remove the crash pad lower panel. (Refer to Body - & ...

    Repeat
    Press the key Set [ RPT] through the TUNE knob or key to repeat the current song. ❈ Press RPT again to turn repeat off. ...